LACE ROOM / FINISHING

 

 

1.         

MILL #1 ROPE PADDER, ROLLS 16” DIA. X 28”, RUBBER OVER RUBBER, PNEUMATIC, WITH STAINLESS STEEL CURVED PAN ABOUT 24” DEEP, HAS 3 ROLLS IN THE BOTTOM, BALDOR 2 HP MOTOR, 575 VOLT

 

 

2.         

BUDGIT – OVERHEAD HOIST 1-TON CAPACITY, TROLLEY, CHAINS AND PUSH BUTTON CONTROLS

 

 

3.         

MILL-MADE 14 ½” RUBBER OVER RUBBER ROPE SQUEEZE PADDER, PNEUMATIC WITH 1 S/S ROLL AND SMALL WATER RECOVERY PAN, 550 VOLT 1 HP MOTOR

 

 

4.         

UNLOADING DOUBLE REEL UNIT, MOTOR DRIVEN, APPROX. 30” WIDE

 

 

5.         

MERROW 70D3B-2 SEWING MACHINE, S/N 251278

 

 

6.         

DINSMORE RAILWAY SEWING MACHINE, APPROX. 230”, UNIT HAS A 1/3 HP 1725 RPM 115/230 VOLT MOTOR

 

 

7.         

MARSHALL & WILLIAMS TENTER FRAME:

·         ENTRY SCROLL ROLL IS 236”.  THIS IS AN OVER AND UNDER M&W FRAME.  UNIT HAS 9” 3-FINGER E&L UNCURLERS S/S, TYPE LAM5/30-7887.  ALSO IT HAS E&L TYPE FR1501 ELECTRIC EYE GUIDING FOR THE ENTRY

·         TENTER HAS A 40’ OPEN INFEED OF RAILS AND CHAIN WITH 4-SECTION ADJUSTABLE.  TENTER WILL OPEN TO 240” MAX AND APPROX. 24” MIN.  TENTER HAS A 2-SECTION DUDLEY GARLAND AND JENSEN DRYER, GAS FIRED, SINGLE BURNER WITH PARTLOW GAS CONTROL

·         EXIT END IS APPROX. 10’ OPEN.  MACHINE IS RUNNING A 15 HP 550 VOLT VARISPEED DRIVE WITH A LOUIS ALLIS GEAR MOTOR.  EXIT END HAS A 2-ROLL SURFACE BATCHER, 235” FACE, 6” DIAMETER ROLLS.  UNIT ALSO HAS A RAILWAY UNIT MOUNTED ON TOP

 

 

 

WAREHOUSE / SHIPPING

 

 

8.         

(2) AMERICAN DRYER CORP. ELECTRIC TUMBLE DRYERS, GALVANIZED DRUM 36” X 36”, DIGITAL CONTROLS, REVERSING

 

 

9.         

MILL-MADE INSPECTION MACHINE, TAKES OFF IN THE BACK, TRUMETER YARDAGE COUNTER, WOODEN BOARD, NO BACKLIGHT, 72” ADJUSTABLE 2-ROLL SURFACE TAKE UP

 

 

10.      

WOONSOCKET NAPPER, 36-ROLL, 120”, PIV DRIVEN, S/N DD1321, WITH FOLDER AND DUST EXHAUST FAN

 

 

11.      

MERROW SEWING MACHINE, MODEL 70D3B-2, S/N 243632

 

 

12.      

ROLLER CRADLE PUT-UP MACHINE, ROLLS ARE 80” X 6” DIA., 4 ROLLS IN THE CRADLE, APPEARS TO BE A MENZEL TYPE

 

 

13.      

MILL-MADE 3-ROLL CRADLE, MANUAL, WOOD FRAME, 3-ROLLS 6 ½” DIA. X 130”

 

 

14.      

DAYTON – FLOOR FAN, 30”, 3-BLADE, MOTOR ½ HP, 115 VOLT

 

 

 

 

FINISHING AREA / BABCOCK FRAME

 

 

15.      

MERROW SEWING MACHINE, MODEL 70ABB-1, S/N 238882

 

 

16.      

BABCOCK / BRUCKNER TENTER FRAME, HORIZONTAL PIN TENTER, CONSISTING OF:

·         BABCOCK PADDER, 140”

·         BIANCO 2-SCROLL ROLL MOTOR DRIVEN ENTRY IN THE AIR PRIOR TO THE PADDER

·         BIANCO DOGGLE UNIT

·         PADDER IS A SINGLE DIP

·         MAHLO ORTHOMAT WEFT STRAIGHTENER (OVER PADDER) WITH 6 SENSING HEADS

·         BRUCKNER TENTER FRAME, TYPE 5001-5400, 4-ZONE GAS FIRED, WILL GO OUT TO APPROX. 150”

·         20’ OPEN ENTRY SECTION

·         HORIZONTAL RAIL

·         ENTRY GUIDERS ARE 3-FINGER E&L MODEL FR1501

·         PINNING BRUSHES

·         PINNING BRUSH CLEANERS

·         ON-FRAME EDGE TRIMMING

·         LOW PROFILE GAS-FIRED DRYER 8-ZONE, TOTAL 45’ LENGTH X 6’ HEIGHT

·         10’ EXIT WITH 5’ COOLING SECTION

·         2-ROLL SURFACE BATCH ON THE FRAME OR KRANTZ AUTOMATIC GUILLOTINE BATCHER

·         KRANTZ AMERICA BATCHER, TYPE 701M, APPROX. 150” MAX., WITH SWING FOLDER, INSPECTION BOARD AND CRADLE

 

 

17.      

24” DAYTON FLOOR FAN, MODEL 4M197, ½ HP

 

 

18.      

(2) AMERICAN DRYERS  #6A & #4A.  ELECTRIC TUMBLE DRYERS, GALVANIZED DRUM 36” X 36”, DIGITAL CONTROLS, REVERSING

 

 

19.      

STAINLESS STEEL PADDLE DYE MACHINE, #P2, APPROX. 600 LB. CAPACITY, 92” WIDE X 84” FRONT-TO-BACK X 47” DEEP, ROUND REEL 90” WIDE, DIVIDER IN MIDDLE OF REEL, ENCLOSED, PNEUMATIC DOORS, DRIVE, ROUND BOTTOM (NOT SELF-DUMPING)

 

 

20.      

STAINLESS STEEL PADDLE DYE MACHINE, #P3, APPROX. 600-800 LB. CAPACITY, 80” WIDE X 60” FRONT-TO-BACK X 48” DEEP, ROUND REEL 72’ WIDE, DIVIDER IN MIDDLE OF REEL, ENCLOSED, PNEUMATIC DOORS, DRIVE, ROUND BOTTOM, AUTO-DUMPING

 

 

 

21.      

STAINLESS STEEL PADDLE DYE MACHINE, #P4, 3-POCKETS, APPROX. 1,000 LB. CAPACITY, 122” WIDE X 108” FRONT-TO-BACK X 54” DEEP, 3 DIVIDERS FOR POCKETS, EACH POCKET 42” WIDE, ROUND REEL IN EACH POCKET 34” WIDE, SPECIALTY HYDRAULIC POWER UNIT WITH MOTOR 7 ½ HP, 230/460 VOLT, ENCLOSED, PNEUMATIC DOORS, SLOPE BOTTOM, DRIVE, ADD TANK APPROX. 70-75 GALLONS CAPACITY, DRIVE, AUTO-DUMPING

 

 

22.      

STAINLESS STEEL PADDLE DYE MACHINE, #P5, APPROX. 200 LB. CAPACITY, 39 ½” WIDE X 60” FRONT-TO-BACK X 39” DEEP, ROUND REEL 36” WIDE, ENCLOSED, MANUAL DOORS, ROUND BOTTOM, DRIVE (NOT SELF-DUMPING)

 

 

23.      

STAINLESS STEEL SAMPLE PADDLE DYE MACHINE, #P6, APPROX. 75 LB. CAPACITY, 24” WIDE X 36” FRONT-TO-BACK X 27” DEEP, ROUND REEL 20” WIDE, ENCLOSED, MANUAL DOORS, SLOPE BOTTOM, DRIVE

 

 

 

 

JET DYE HOUSE

 

 

24.      

(2) FONGS JETS, ATMOSPHERIC, 2-PORT, 4-STRAND, MODEL GN9-100-2T, YEAR 1994.  EACH UNIT HAS A S/S TANK WITH WASH RING AND MIXER. BOTH HAVE FILTERS.

UNITS HAVE FONGS CONTROLS MODEL 1001

UNITS MAY BE COUPLED TO FORM A 4-PORT, 8-STRAND MACHINE

 

 

25.      

MERROW SEWING MACHINE, MODEL 70D3B, #167909

 

 

26.      

MILL-MADE PUT UP MACHINE, APPROX. 72” WIDE, (2) S/S SCROLL ROLLS MOUNTED, DRIVEN, ON A RACK.  TAKING ROPE FORM GOODS FROM THE JETS AND PUTTING THEM INTO OPEN WIDTH.

 

 

27.      

MERROW SEWING MACHINE, MODEL 70DB3, S/N 181644

 

 

28.      

MERROW SEWING MACHINE, MODEL 70-ABB-1, S/N 227836

 

 

29.      

CEILING-MOUNTED SWING FOLDER WITH DRIVE, 60”

 

 

 

 

BACK DYE ROOM

 

 

30.      

RIGGS & LOMBARD – SAMPLE DYE BEC, #B69, ENCLOSED, 24” WIDE X 60” FRONT-TO-BACK X 40” DEEP, ROUND REEL, MANUAL DOOR, DRIVE

 

 

31.      

K.W.G. – PADDLE DYE MACHINE, ENCLOSED, #P1, MODEL A100, 250 LB. CAPACITY, S/N M743, 396 GALLONS CAPACITY, 42” WIDE X 60” FRONT-TO-BACK X 48” DEEP, DRIVE, MANUAL DOOR (UNABLE TO VIEW REEL)

 

 

32.      

STAINLESS STEEL DYE BECK, 72” WIDE X 84” FRONT-TO-BACK X 40” DEEP, ENCLOSED, OVAL REEL, 7-BAR DIVIDERS, MANUAL FRONT AND REAR DOORS, DRIVE

 

 

33.      

STAINLESS STEEL DYE BECK, 72” WIDE X 108” FRONT-TO-BACK X 40” DEEP, ENCLOSED, OVAL REEL, 8-BAR DIVIDERS, MANUAL FRONT AND REAR DOORS, DRIVE

 

 

34.      

SAMPLE DYE BECK, 14” WIDE X 24” FRONT-TO-BACK X 12” DEEP, SLOPE BOTTOM, DRIVE, PORTABLE STAND (UNABLE TO VIEW REEL)

 

 

35.      

GASTON COUNTY – SINGLE PORT JET, MODEL H, NATIONAL BOARD #9037, 53 PSI AT 300 DEGREES, S/N 720884, YEAR 1972, HEAT EXCHANGER, ADD TANK APPROX. 75 GALLONS CAPACITY, FULL ONE PORT

 

 

36.      

GASTON COUNTY – SINGLE PORT JET, MODEL H, APPEARS CONVERTED TO MODEL 824, NATIONAL BOARD #8893, S/N 720795, YEAR 1972, HEAT EXCHANGER, ADD TANK APPROX. 75 GALLONS CAPACITY

 

 

37.      

STAINLESS STEEL PADDLE DYE MACHINE, #P7, ENCLOSED, APPROX. 350 LB. CAPACITY, 96” WIDE X 48” FRONT-TO-BACK X 30” DEEP, ROUND PADDLE 90” WITH DIVIDER IN MIDDLE, PNEUMATIC FRONT AND REAR DOORS, DRIVES AND CONTROLS

 

 

38.      

STAINLESS STEEL TANK APPROX. 100-125 GALLONS CAPACITY WITH VERTICAL AIR MIXER, SHAFT APPROX. 36” AND 2 SETS SMALL BUTTERFLY PADDLES

 

 

 

 

MAIN DYE ROOM

 

 

39.      

RIGGS & LOMBARD – DYE BACK, #S2, ENCLOSED, SLOPE BOTTOM, 24” WIDE X 48” FRONT-TO-BACK X 42” DEEP, ROUND SOLID REEL, DRIVE

 

 

40.      

DYE BECK, OPEN, 24” WIDE X 84” FRONT-TO-BACK X 36” DEEP, OVAL REEL, DRIVE

 

 

41.      

RODNEY HUNT – TRU-SHADE DYE BECK, SEMI-ENCLOSED, 72” WIDE X 84” FRONT-TO-BACK X 56” DEEP, SLOPE BOTTOM, ROUND SLOTTED REEL, DRIVE

 

 

42.      

RODNEY HUNT – TRU-SHADE OPEN DYE BECK, S/N 7321, 120” WIDE X 84” FRONT-TO-BACK X 56” DEEP, ROUND SLOTTED REEL, DRIVE, WITH ADD TANK APPROX. 75-100 GALLONS CAPACITY

 

 

43.      

RODNEY HUNT – TRU-SHADE OPEN DYE BECK, 72” WIDE X 84” FRONT-TO-BACK X 56” DEEP, OVAL SLOTTED REEL, DRIVE

 

 

44.      

RIGGS & LOMBARD – OPEN DYE BECK, 36” WIDE X 80” FRONT-TO-BACK X 36” DEEP, OVAL SLOTTED REEL, DRIVE

 

 

45.      

(2) RIGGS & LOMBARD – OPEN DYE BECKS, 72” WIDE X 90” FRONT-TO-BACK X 58” DEEP, OVAL REEL, DRIVE

 

 

46.      

MAT – STAINLESS STEEL FULLING MILL

 

 

47.      

CONSEW – BAG CLOSER, MODEL 10, ON PEDESTAL WITH TRANSMITTER AND MOTOR

 

 

48.      

RODNEY HUNT – TRU-SHADE DYE BECK, SEMI-ENCLOSED, S/N 7492, 72” WIDE X 90” FRONT-TO-BACK X 48” DEEP, OVAL REEL, DRIVE

 

 

49.      

RODNEY HUNT – TRU-SHADE OPEN DYE BECK, S/N 7070, 72” WIDE X 90” FRONT-TO-BACK X 48” DEEP, OVAL REEL, DRIVE

 

 

50.      

SAMPLE DYE BECK, OPEN, 24” WIDE X 84” FRONT-TO-BACK X 36” DEEP, OVAL SLOTTED REEL, DRIVE

 

 

 

51.      

SIRUBA-STYLE BAG CLOSER WITH PEDESTAL, TRANSMITTER AND MOTOR

 

 

52.      

RODNEY HUNT – TRU-SHADE ENCLOSED DYE BECK, S/N 7421, 72” WIDE X 84” FRONT-TO-BACK X 56” DEEP, ROUND REEL, DRIVE

 

 

53.      

RODNEY HUNT – TRU-SHADE OPEN SLACK LOOP WASHER, S/N 7618, REAR RUBBER/RUBBER PNEUMATIC SQUEEZE ROLLS 14” DIA. X APPROX. 9 ½ FEET WIDE, UNIT IS 10’ WIDE X 84” FRONT-TO-BACK (APPROX. 30” DEEP), 20 ROPES CAPACITY, ADD TANK WITH VERTICAL MIXER APPROX. 110-120 GALLONS CAPACITY, DRIVE AND CONTROLS

 

 

54.      

(2) MILL-MADE SAMPLE DYE BECKS, OPEN, 36” WIDE X 42” FRONT-TO-BACK X 32” DEEP, HEXAGONAL SLATTED REELS, DRIVE

 

 

55.      

CUSTOM-MADE ENCLOSED DYE BECK, (MILL #21), 96” WIDE X 108” FRONT-TO-BACK, SHALLOW DEPTH (APPROX. 2’), PNEUMATIC DOORS FRONT AND REAR, OVAL REEL, MODERN STYLE CONTROLS, REVERSING, DRIVE

 

 

56.      

ENCLOSED DYE BECK, 36” WIDE X 72” FRONT-TO-BACK X 60” DEEP, ROUND ANGLED-BAR REEL, MANUAL DOORS, DRIVE

 

 

57.      

ENCLOSED DYE BECK, 36” WIDE X 96” FRONT-TO-BACK X 36” DEEP, SLOPE BOTTOM, OVAL REEL, DRIVE

 

 

58.      

RODNEY HUNT – TRU-SHADE ENCLOSED SAMPLE DYE BECK, S/N 7943, 24” WIDE X 90” FRONT-TO-BACK X 58” DEEP, OVAL REEL, DRIVE

 

 

59.      

(2) OPEN DYE BECKS, 66” WIDE X 80” FRONT-TO-BACK X 36” DEEP, OVAL SLATTED REEL, DRIVE

 

 

60.      

(2) CENTRIFUGAL EXTRACTORS, ONE IS A TROY, OTHER UNKNOWN, 60” DIA. WITH SPARE COVER, MOTOR ESTIMATED 10-20 HP, MANUAL COVER LOCK

 

 

61.      

RODNEY HUNT – DOUBLE BOX FULLING MILL, ROLLS RUBBER/RUBBER, 6’ TOTAL WIDTH, WOOD BOTTOM, FIBERGLASS LINING, GEAR MOTOR DRIVE ESTIMATED 5-10 HP, ADD TANK APPROX. 50-60 GALLONS CAPACITY

 

 

62.      

GASTON COUNTY – 3-PORT JET, NATIONAL BOARD #10175, S/N 740138, YEAR 1974, DRIVE AND CONTROLS, ADD TANK APPROX. 50 GALLONS CAPACITY

 

 

63.      

GASTON COUNTY – 3-PORT JET CONVERTED TO “J” SERIES, I.D. PLATE NOT VISIBLE (DUE TO PLACEMENT), SEPARATE TALL PANEL CONTROL, DRIVE, ADD TANK APPROX. 50 GALLONS CAPACITY

 

 

 

 

 

LAB

 

 

64.      

BROWN & SHARPE – HAND SKEIN REELER, 12” DIA.

 

 

65.      

CORNING – STIRRER/HOTPLATE APPROX. 12” X 12”

 

 

66.      

APPLE – PERSONAL COMPUTER, MODEL NOT VISIBLE, 21” COLOR MONITOR

 

 

67.      

HEWLETT-PACKARD – LASERJET PRINTER MODEL 4200

 

 

68.      

(2) GRETAG-MACBETH – BENCH SPECTRALIGHT III DAYLIGHT MACHINES, MODEL AND SERIAL NUMBER PLATE NOT VISIBLE, 35” WIDE X 24” DEEP X 26” HEIGHT OF BOX INTERIOR, 4-TUBE LIGHT

 

 

69.      

CENTRAL SCIENTIFIC/CENCO – ELECTRIC BENCH OVEN, CATALOG #95379-17, 1600 WATTS, 230 VOLT ELECTRICS, 50/60 HZ, STAINLESS STEEL INTERIOR 16” X 14” X 21”, 3 SHELVES

 

 

70.      

GRIEVE – ELECTRIC BENCH OVEN, MODEL NB-350, 450 DEGREE MAX. TEMP., 2000 WATTS, 115 VOLT SINGLE PHASE ELECTRICS, 50/60 HZ, STAINLESS STEEL INTERIOR 28” X 25” X 18”, 2 SHELVES

 

 

71.      

AHIBA – NUANCE TOP SPEED BENCH SAMPLE DYE MACHINE, DATA PLATE ON REAR NOT VISIBLE, WITH CANISTERS AND ASSOCIATED EQUIPMENT

 

 

72.      

(2) AHIBA – NUANCE TOP SPEED BENCH SAMPLE DYE MACHINES, REAR COVER THAT HAS DATA PLATE IS MISSING, WITH MANY CANISTERS AND ASSOCIATED EQUIPMENT SCATTERED THROUGHOUT THE LAB

 

 

73.      

AHIBA – TEXOMAT BENCH LAB DYE MACHINE, DATA PLATE NOT VISIBLE (DUE TO PLACEMENT), 12-SPINDLE WITH LARGE AMOUNT OF SPARE SPINDLES AND CANISTERS

 

 

74.      

ACC-LAB/SARTORIUS – “VICON” BENCH DIGITAL BALANCE, MODEL VIC-412, STAINLESS STEEL PLATFORM, PLASTIC COVER

 

 

75.      

ATLAS – AATCC BENCH CROCKMETER, MODEL CM-1

 

 

76.      

CORNING – BENCH STIRRER/HOTPLATE MODEL PC-6200, CERAMIC PLATFORM 11” X 10”

 

 

77.      

CIMAREK – BENCH STIRRER/HOTPLATE, MODEL NUMBER NOT VISIBLE, PLATFORM 8” X 8”

 

 

78.      

KENMORE – ELECTRIC WASHER AND DRYER SET, “ULTRA FABRIC CARE”, 80 SERIES

 

 

79.      

(2) MANUAL PERSPIRATION TESTERS ON A SHELF, SIMILAR TO ATLAS, BUT MOST OF THE PLATES NOT VISIBLE

 

 

80.      

DATACOLOR/AHIBA – BENCH FLIP-TOP LAB DYE MACHINE, TYPE PM-100, 6600 WATTS, 36 AMPS, AHIBA 1000 CONTROLLER

 

 

81.      

HEWLETT-PACKARD – LASERJET PRINTER MODEL 4250 WITH OLDER H-P PERSONAL COMPUTER

 

 

82.      

LAB-LINE – ELECTRIC BENCH OVEN, SERIES IMPERIAL V, DATA PLATE NOT VISIBLE (DUE TO PLACEMENT), OPERATING AND UNABLE TO VIEW INTERIOR, DOOR 21 ½” WIDE X 26” HEIGHT, TOTAL FRONT-TO-BACK ON OVEN EXCLUDING THE DOOR IS 21 ½”, DIGITAL MODERN CONTROLS

 

 

83.      

DATACOLOR – COLOR MATCHING SYSTEM WITH “SPECTRUM” ANALYZER SERIES 600, DATA PLATE NOT VISIBLE (DUE TO PLACEMENT), WITH DELL PERSONAL COMPUTER “DIMENSION 8400” AND 17” FLAT COLOR MONITOR, DISCS, CONNECTORS, ETC.

 

 

84.      

LOT OF ASSORTED UNLISTED GLASSWARE SUCH AS BEAKERS, CYLINDERS, PIPETTES AND JARS, PLUS SMALL ELECTRONIC GAUGES, ETC.

 

 

85.      

FURNITURE AND APPARATUS, CONSISTING OF:

(2) CHROME-LEG METAL DESKS 30” X 60”

(2) HON 3-DRAWER LATERAL FILES, 42”

(1) SAMSUNG – UNDER-COUNTER REFRIGERATOR, APPROX. 8 CU. FT. CAPACITY

(1) AMERICANA – OLDER 4-BURNER GAS STOVE

(9) METAL 2-DRAWER LETTER FILE CABINETS

(1) SHARP – COPIER, MODEL AR-P350

(1) SHARP – COPIER, MODEL AR-M450U

(1) MAGIC CHEF – UNDER-COUNTER REFRIGERATOR APPROX. 8 CU. FT. CAPACITY

(1) HON – 4-DRAWER LATERAL FILE CABINET, 42”

(3) METAL 4-DRAWER LETTER FILE CABINETS

(1) WOODEN DESK 36” X 72”

(7) ASSORTED HI-BACK EXECUTIVE CHAIRS

 

 

 

 

 

AIR COMPRESSORS

 

 

86.      

CHAMPION RECEIVER-MOUNTED Y-TYPE PISTON AIR COMPRESSOR, V-BELT DRIVE AND MOTOR 10 HP, 1745 RPM, 575 VOLT, YEAR 1987 ON TANK OF APPROX. 120 GALLONS, NO HOUR METER

 

 

87.      

GARDNER-DENVER RECEIVER-MOUNTED ROTARY SCREW AIR COMPRESSOR, 125 PSI, ON MAIN FILTER IS MODEL 1214-778 AND YEAR 1992, MOTOR 30 HP, 1760 RPM, 575 VOLT, APPROX. 120-150 GALLON TANK, ALL DIGITAL READOUTS, SELF-MONITORING, 8,420 HOURS SHOWING ON METER, NO COVER

 

 

88.      

ZEKS “HEAT SINK” REFRIGERATED AIR DRYER, MODEL 125HSEA100, S/N 119627-2, YEAR 1992, 100 SCFM, 1 ½ HP, 115 VOLT, R-22 REFRIGERANT

 

 

89.      

INGERSOLL-RAND OLDER STYLE RECEIVER-MOUNTED Y-TYPE PISTON AIR COMPRESSOR, TYPE 30, MODEL 253D5, S/N 30T 266398, V-BELT DRIVE AND MOTOR 5 HP, 1715 RPM, 575 VOLT, APPROX. 80 GALLON TANK, NOT IN USE AT TIME OF INSPECTION, APPEARS BACKUP USE ONLY.

 

 

90.      

KAESER ROTARY SCREW AIR COMPRESSOR MODEL SM11, 26,616 HOURS SHOWING ON METER, S/N NOT VISIBLE, APPROX. 10 HP, WITH COVER AND VERTICAL AIR RECEIVER 30” DIA. X 60”, NEAR DYE HOUSE, BASEMENT LEVEL

 

 

91.      

KAESER REFRIGERATED AIR DRYER MODEL KRD 050, DATA PLATE NOT VISIBLE DUE TO PLACEMENT OF DRYER, APPROX. 50-100 SCFM, NEAR DYE HOUSE, BASEMENT LEVEL

 

 

92.      

DAYTON RECEIVER-MOUNTED Y-TYPE AIR COMPRESSOR, V-BELT DRIVE AND MOTOR 5 HP, 1725 RPM, 230 VOLT, APPROX. 120 GALLON TANK, NO LONGER IN USE, DISCONNECTED AND STORED – IN CORNER NEAR INSPECTION AREA, UPPER AREA

 

 

 

 

ELECTRIC POWER ROOM

(NEXT TO SEWING MACHINE SHOP AREAS)

 

 

93.      

LARGE LOT ELECTRICAL SUPPLIES SUCH AS WIRE, CONDUIT, LIGHT FIXTURES, JUNCTION BOXES, CONNECTORS, ELBOWS AND T’s, FUSES, CONTROL BOXES, CIRCUIT BREAKERS, ETC., MIXTURE OF NEW AND USED – CONSIDERED CONSUMABLES (STOCK AND SUPPLY ITEMS) AND NOT WITHIN SCOPE OF APPRAISAL

 

 

 

 

SEWING AREA PLUS MACHINE SHOP ADJOINING

 

 

94.      

UNION SPECIAL 4-THREAD SERGER/OVERLOCK SEWING MACHINE, SINGLE NEEDLE, MODEL PLATE ON REAR AND UNABLE TO READ DUE TO PLACEMENT, APPEARS TO BE 39500 SERIES, DARK BRONZE HEAD WITH TABLE, TRANSMITTER AND MOTOR

 

 

95.      

PFAFF 4-THREAD HIGH LOFT “CORNERS” SEWING MACHINE, DOUBLE NEEDLE, NEEDLE FEED, DESIGNATION #142-720/01, ALSO SHOWS DESIGNATION 6/01BS, S/N 759701, REVERSE LEVER, UP/DOWN VERTICAL CORNERING LEVER, TABLE, TRANSMITTER AND MOTOR

 

 

96.      

(4) MILL-MADE BLOCKING / WINDING MACHINES, RANGE 4” – 8” WIDTHS, UNDERSLUNG SEWING MACHINE DRIVE AND TRANSMITTER, ON ROLLING 2 SHELF CART

 

 

97.      

MERROW BLACK HEAD SINGLE NEEDLE 2-THREAD SEWING MACHINE, I.D. PLATE COVERED OVER, SIMILAR TO MODEL A-3DW, TABLE, TRANSMITTER AND MOTOR

 

 

98.      

MERROW SEWING MACHINE, MODEL 70-ABB-1, S/N 227833, SINGLE NEEDLE, 2 THREADS, TABLE, TRANSMITTER AND MOTOR

 

 

99.      

SINGER BLANKET SEWING MACHINE, ZIG-ZAG, MODEL “457 PLUS”, SINGLE NEEDLE, 2 THREADS, TABLE, TRANSMITTER AND MOTOR

 

 

100.   

MERROW “CROCHET” SEWING MACHINE, GREEN HEAD, STYLE 17-F, S/N 232228, ON MILL-MADE LARGE TABLE, TRANSMITTER AND MOTOR

 

 

101.   

MERROW SEWING MACHINE, MODEL 70-D3B, S/N 167874, SINGLE NEEDLE, SINGLE THREAD, TABLE, TRANSMITTER AND MOTOR

 

 

102.   

GROUP OF LOW VALUE SEWING ITEMS, CONSISTING OF:

(3) MILL-MADE WOODEN CLOTH CUTTING TABLES 4’ X 8’, MASONITE TYPE TOP

(3) OLDER TYPIST CHAIRS

(1) PLASTIC PEDESTAL FAN

(1) MAIMIN KNIFE CLOTH CUTTER, IN MACHINE SHOP, APPROX. 6” KNIFE, APPEARS INOPERABLE, PARTS ONLY

(1) MINI BENCH DOUBLE END GRINDER USED AS NEEDLE SHARPENER, 5”, NEEDLE HOLDING ATTACHMENT, NEWER, IN MACHINE SHOP

 

 

 

103.   

WEIGHTRONIX FLOOR SCALE, MODEL DSL484805, 5000 LB. CAPACITY, PLATFORM 4’ X 4’, S/S DIGITAL HEAD – DISCONNECTED, NO LONGER IN USE.

 

 

104.   

SOUTH BEND OLDER STYLE BELT DRIVE LATHE, CATALOG #CL-179H, 12’ BED, APPROX. WWII VINTAGE, RAISED 5”, NOW 24” SWING X APPROX. 120” CENTER DISTANCE INCLUDING RAISE BLOCKS, 1 Ύ” HOLE THROUGH SPINDLE, SPEEDS APPROX. 24-224 RPM, THREADING EQUIPMENT, TAPER ATTACHMENT, 4 JAW CHUCK, FACEPLATE, CENTER RESTS AND LARGE ASSORTMENT OF ASSOCIATED TOOLING IN CHIP PAN, MOTOR IN BASE.

 

 

105.   

MERROW SEWING MACHINE, MODEL 70-D3B, S/N 223821, WITH TABLE, TRANSMITTER AND MOTOR – DISASSEMBLED FOR REPAIR

 

 

106.   

OWATONNA H-FRAME SHOP PRESS, MODEL B, 17 ½ TONS CAPACITY, WITH HYDRAULICS

 

 

107.   

SOUTH BEND PRECISION LATHE, CATALOG #818745, 4’ BED, SIZE 10” SWING, APPROX. 36” CENTER DISTANCE, 1 Ύ” HOLE THROUGH SPINDLE, SPEEDS 4-224 RPM, 3 AND 4-JAW CHUCKS, THREADING EQUIPMENT, TAPER ATTACHMENT, CABINET BASE AND MOTOR, LARGE ASSORTMENT OF ASSOCIATED TOOLING, GOOD CONDITION FOR AGE.

 

 

108.   

HORIZONTAL METAL CUTTING BANDSAW, OLDER STYLE, MANUAL, APPROX. 16” X 16”, MOTOR 1 HP, 550 VOLT (CANNOT SEE MFR’S NAMEPLATE, RESEMBLES KALAMAZOO)

 

 

109.   

INFINITEX “SPLITTER” POWER PORTABLE WATER FILTRATION SYSTEM, NO MODEL PLATE VISIBLE, 15 AMPS, 120 VAC, S/N 1222, GRUNDFOS VERTICAL S/S PUMP APPROX. 1 ½” WITH 3 HP DIRECT DRIVE MOTOR, 230/460 VOLT, HOSES, CART AND UNLISTED ASSOCIATED EQUIPMENT

 

 

110.   

OSTER “PIPE-MASTER” PIPE THREADING MACHINE, NO DATA PLATE VISIBLE, 2 ½” HOLE THROUGH CHUCK, WITH RIDGE TOOL LARGE DIE HEAD (BEHIND THE BANDSAW PREVIOUSLY DESCRIBED) PLUS SET OF 8 RIDGE TOOL DIE HEADS AND RATCHETS, OTHER MISCELLANEOUS PIPE TOOLING IN AREA, CART, MOTOR

 

 

111.   

MERROW SEWING MACHINE HEAD MODEL MG-3DW, S/N 324662, GREEN, With TRANSMITTER AND MOTOR – DISASSEMBLED FOR REPAIR

 

 

 

112.   

GROUP OF LINK-BELT P.I.V. UNITS, CONSISTING OF:

(2) MODEL V-2-30A

(2) MODEL V-1-50

(1)     WITHOUT TAG, APPROX. SIZE V-1/2-20

 

 

113.   

GROUP OF 8-10 UNLISTED MISCELLANEOUS ELECTRIC OR BATTERY OPERATED POWER TOOLS SUCH AS SAWZALL, ANGLE GRINDER, SCREWDRIVERS, DRILLS, CIRCULAR SAWS, ETC.

 

 

114.   

GROUP OF UNLISTED HAND TOOLS ON BENCHES, IN CABINETS AND TOOL BOXES

 

 

115.   

GROUP OF LOWER VALUE ITEMS, CONSISTING OF BUT NOT LIMITED TO:

(1) HAMMOND OLDER DOUBLE END GRINDER, MODEL OK-10, S/N 3738, 10”, MOTOR 1 HP, 550 VOLT

(1) SINGLE END 6” BENCH GRINDER

(1) WILTON LARGE BENCH VISE, MODEL C-3, 6”

(1) CRAFTSMAN OLDER FLOOR DRILL, 15” SWING

(1) DELTA FLOOR DRILL, 15” SWING, S/N 63-1993, 1 ½ HP, WITH 6” VISE

(1) BROWN & SHARPE PLAIN HORIZONTAL MILLING MACHINE, #2, APPROX. WWII VINTAGE, TABLE 10” X 48”, UNIVERSAL MILLING ATTACHMENTS, COOLANT, 6” UNIVERSAL VISE AND ASSORTED TOOLING

(1) OXY-ACETYLENE TORCH WITH CART

(1) MINI PNEUMATIC GUN-TYPE LAB MIXER

(1) MINI 2 HP PORTABLE AIR COMPRESSOR

(1) GRINDING ATTACHMENT FOR LATHE, SEEN UNDER A BENCH

ASSORTED UNLISTED SMALL PUMPS OF ALL SORTS, FLOOR JACKS, HAND-GEARED HOISTS, ETC.

 

 

116.   

GROUP OF ASSORTED UNLISTED MACHINE PARTS ON BENCHES, IN CABINETS AND ON FLOOR, INCLUDING BUT NOT LIMITED TO:  SPROCKETS, GEARS, CHAINS, BEARINGS, DRIVE SETS AND MOTORS, DRIVE BELTS, MISCELLANEOUS UNIDENTIFIED OTHER SPARE PARTS – CONSIDERED CONSUMABLES (STOCK AND SUPPLY ITEMS) AND NOT WITHIN SCOPE OF APPRAISAL – NO VALUE ASSIGNED

 

 

 

 

OFFICES

 

 

117.   

SHARP FULL SIZE COPIER, MODEL MX-MISSION, FULLY FEATURED, WITH 2-TRAY COLLATOR

 

 

118.   

ATLAS CROCKMETER, MODEL CM-1, S/N 9768 D19, A.A.T.C.C.

 

 

119.   

GROUP OF OFFICE FURNITURE AND EQUIPMENT, CONSISTING OF BUT NOT LIMITED TO:

·         CUBICLE STYLE 2-DRAWER METAL FILE CABINET

·         (3) WOODEN L-SHAPE SECRETARIAL DESKS, DARK MAHOGANY FINISH (WORN)

·         (2) LEATHER-UPHOLSTERED HIGH BACK EXECUTIVE CHAIRS, WOODEN PEDESTAL, LEATHER PADDED ARMRESTS

·         BLOND WOOD NEWER DESK 30” X 60” WITH OLDER STYLE ROUND-BACK WOODEN CHAIR

·         WOODEN 2-DRAWER LATERAL FILE CABINET, 36”

·         STEEL CUBICLE STYLE 2-SHELF STORAGE CABINET, 42”, SLIDING DOORS

·         RACETRACK SHAPED WOODEN CONFERENCE TABLE 36” X 8’, MAHOGANY FINISH, WITH 4 WIDE SEAT DEEPLY PADDED MATCHING ARMCHAIRS, UPHOLSTERED ARMRESTS (CHAIRS SCATTERED THROUGHOUT OFFICES)

·         MODERN STYLE NEWER BEVELLED-EDGE WOODEN DESK, WALNUT FINISH, WITH MATCHING CREDENZA

·         LEATHER-UPHOLSTERED HIGH BACK EXECUTIVE CHAIR, WOODEN PEDESTAL AND ARMS

·         SQUARE-EDGE TABLE/DESK, WOODEN, 3’ X 6’, SLAB SUPPORTS

·         (2) HON 3-DRAWER METAL LATERAL FILE CABINETS, 42”

·         HON 4-DRAWER METAL LATERAL FILE CABINET, 42”

·         MINI WOODEN END TABLE, MAHOGANY FINISH

·         CUBICLE STYLE METAL 3-DRAWER FILE CABINET, ON CASTERS

·         NEWER WOODEN PRINTER TABLE 30” X 60”, METAL LEGS

·         DANBY S/S CLAD REFRIGERATOR, APPROX. 8 CU. FT. CAPACITY

·         (3) ANDERSON-MICKEY METAL 2-DRAWER FILE CABINETS, DEEP LENGTH

·         STAPLES SHREDDER, 30”, MODEL SPL-S 302D WITH BASKET

·         (4) RECEPTION ARMCHAIRS, WOODEN, MAHOGANY FINISH, FULL BACK

·         PRE-ENGINEERED PORTABLE MICROWAVE TABLE/CABINET WITH G.E. SMALL MICROWAVE OVEN

·         UNLISTED ASSORTED OFFICE ITEMS SUCH AS IN/OUT TRAYS, STAPLERS, TAPE DISPENSERS, CALCULATORS, POSTAL SCALES, BULLETIN BOARDS, ETC.

 

 

120.   

ADC WALL-MOUNTED KEY CARD SYSTEM AT ENTRY – CONSIDERED PART OF REAL ESTATE DUE TO METHOD OF ATTACHMENT AND CUSTOMARY USE – NO VALUE ASSIGNED

 

 

 

 

DATA PROCESS ITEMS IN OFFICE AREA

 

 

121.   

(4) HEWLETT-PACKARD BASIC PERSONAL COMPUTERS, WITH BASIC INKJET COLOR PRINTER AND FLAT SCREEN 15” MONITOR, FAX MODEM, ONLY ONE SHARED APC UPS (TAPE) BACKUP UNIT SEEN.  NOTE:  NO MODEL INDICATED ON ANY, FROM OTHER MISCELLANEOUS LABELS YEAR APPEARS TO BE 2002 AVERAGE)

 

 

122.   

HEWLETT-PACKARD LASERJET PRINTER MODEL 4250

 

 

123.   

“PRONTO” LASER THERMAL LABEL PRINTER

 

 

124.   

REMAINDER = ITEMS FOR TELEPHONE SYSTEM WHICH IS INTEGRAL PART OF DATA PROCESS HERE, VIDEOS AND MOVIES CONNECTIONS, ETC.

 

 

125.   

HEWLETT-PACKARD – GROUP OF 3 SWITCHES ?? SETS AND MAIN TELEPHONE CONNECTOR SET WITH SURGE PROTECTORS, ETC. – UNABLE TO OBTAIN MODELS OR INFO ON WHAT THESE SETS WERE.  ALL IN A LARGE FAN-COOLED CABINET BESIDE A DESK.

 

 

126.   

PELCO SEQUENTIAL VIDEO SWITCHER MODEL VS5008

 

 

127.   

GYYA OR GYYR ?? HIGH DENSITY TIME LAPSE, NO MODEL NUMBER VISIBLE WITH STOP/PLAY/EJECT – VCR?

 

 

128.   

(5) ASSORTED DESKTOP TELEPHONES (MORE IN LABS?)

 

 

 

 

BOILER HOUSE & MAINTENANCE AREA

 

 

129.   

CLEAVER-BROOKS PACKAGED FIRETUBE BOILER, COMBINATION GAS AND #2 OIL FIRED, MODEL CB200-500, S/N L-85673, YEAR 1989, 500 HP 150 PSI, 200 VOLTS, 20,920,000 BTU INPUT, WITH STACK, FEEDWATER AND CONDENSATE RETURN PUMPS, WATER TREATMENT ITEMS, PIPING

 

 

130.   

CLEAVER-BROOKS PACKAGED FIRETUBE BOILER, COMBINATION GAS AND #6 OIL FIRED, MODEL CB600-400, S/N L-65390, YEAR 1978, 400 HP, 150 PSI, 460 VOLTS, 16,738,000 BTU/HR. INPUT, WITH STACK, FEEDWATER AND CONDENSATE RETURN PUMPS, WATER TREATMENT ITEMS, PIPING

 

 

131.   

CLEAVER-BROOKS PACKAGED FIRETUBE HEATING BOILER, COMBINATION GAS/OIL FIRED, MODEL CBH700-40, S/N L-75170, YEAR 1981, 15 PSI, APPROX. 100 HP, 480 VOLTS, 1,674,000 BTU/HR INPUT, WITH ACCESSORIES AS THE PREVIOUS TWO BOILERS – NOT IN USE AT TIME OF INSPECTION – CONSIDERED PART OF REAL ESTATE DUE TO CUSTOMARY USE – NO VALUE ASSIGNED.

 

 

132.   

LARGE GROUP OF MISCELLANEOUS ITEMS IN BOILER AREA SUCH AS, BUT NOT LIMITED TO:  AXIAL FANS, REMAINS OF OLDER ELECTRIC HOISTS, PUMPS, ETC., NOT IN USE, STORED, SCRAP VALUE ONLY

 

 

133.   

MILLER PORTABLE AC/DC WELDER, MODEL “SYNCHROWAVE 250”, S/N KA909558, 250 AMPS, 230/460 VOLTS, WITH LEADS, GUN CART, HELMET

 

 

134.   

MILL-MADE ENCLOSED S/S DE-AERATOR TANK 42” WIDE X 6’ LENGTH X 5’ HEIGHT WITH INTERNAL EQUIPMENT PLUS 2 S/S SINGLE SUCTION CENTRIFUGAL PUMPS APPROX. 1 ½” X 1 ½”, NO DATA PLATE VISIBLE, DIRECT DRIVE WITH MOTOR ESTIMATED 10-15 HP AND 3600 RPM

 

 

135.   

MILLER DC PLASMA CUTTER SYSTEM, MODEL SPECTRUM 500, S/N KC321549, 50 AMPS, 115/230 VOLTS, CART, LEADS AND GUN

 

 

136.   

MILLER ROCKER ARM SPOT WELDER, FOOT-TRIP, MODEL 10FTP, 45 AMPS, APPROX. 12” ARM WITH PNEUMATIC ASSIST, OLDER UNIT, FAIR CONDITION

 

 

 

137.   

GROUP OF LOWER VALUE ITEMS, CONSISTING OF BUT NOT LIMITED TO:

·         BENCH OLDER JIGSAW

·         PORTABLE 2 HP MINI AIR COMPRESSOR APPEARS NOT OPERABLE

·         ACME MANUAL STRAPPING MACHINE WITH CART

·         OXY-ACETYLENE TORCH SET WITH CYLINDERS ALONG WALL

·         RYOBI 10” NEWER TABLE SAW WITH EXTENSION WINGS AND STAND

·         DEWALT NEWER 12” BENCH ABRASIVE DISC (CHOP) SAW

·         ASSORTED UNLISTED SMALL HAND AND POWER TOOLS, PIPE VISE AND MANUAL PIPE EQUIPMENT, BOILER ACCESS LADDERS, OTHER MAINTENANCE EQUIPMENT

 

 

 

 

INSPECTION AREA

 

 

138.   

JOHNSON HORIZONTAL BANDSAW, MODEL J, S/N 16005, MILL-MADE MANUAL LONG LENGTH INFEED TABLE FOR LACE ROLLS

 

 

139.   

PENNSYLVANIA – DIGITAL FLOOR SCALE, MODEL 7400, 5000 LB. CAPACITY, S/N 98248996, YEAR 1996, DIAMOND PLATE PLATFORM 4’ X 4’, HEAD MOUNTED ON WALL

 

 

140.   

(2) MANUAL STRAPPING MACHINES WITH TOOLS AND STRAPPING, NEWER UNITS

 

 

141.   

TOLEDO ROLLING PILLAR TYPE DIAL SCALE, 500 LB. CAPACITY WITH 300 LB. BEAM ATTACHMENT, PLATFORM APPROX. 2’ X 2’, ½ LB. GRADUATIONS

 

 

142.   

(8) HAND TRUCKS, SEVERAL ARE IN OTHER AREAS, 3 ARE HEAVY-DUTY ALUMINUM FOR APPLIANCES

 

 

 

 

MISCELLANEOUS BASEMENT AREAS & DYE HOUSE(S)

 

 

143.   

(9) OLDER STORED MOTORS AVERAGE APPROX. 5 HP

 

 

144.   

EARLY STYLE EMERGENCY ELECTRIC GENERATOR, WATER-COOLED, NO I.D. PLATES VISIBLE, WEIGHT ESTIMATED AT 7-8,000 LBS., ESTIMATED 50-100 KVA

 

 

145.   

DETECTO ROLLING DIAL SCALE, 125 LB. CAPACITY WITH ADDITIONAL 125 LB. BEAM ATTACHMENT, PLATFORM 19” X 20”, ON CART

 

 

146.   

(2)  METAL 4-DRAWER LATERAL FILE CABINETS, 42”

 

 

147.   

LINCOLN PORTABLE AC/DC WELDER, MODEL IDEALARC 250, 250 AMPS DC, 300 AMPS AC, 30 VOLTS, WITH LEADS, GUN, HELMET, WELDING RODS AND CART

 

 

148.   

(2) JUSTRITE FLAMMABLES STORAGE CABINETS, MODEL 25701, 55 GALLONS CAPACITY, SELF-CLOSING DOOR (NEAR BABCOCK FRAME)

 

 

149.   

WEIGH-TRONIX FLOOR SCALE, MODEL DSL4848-05, DIAMOND PLATE PLATFORM 4’ X 4’, 5000 LB. CAPACITY, S/S DIGITAL HEAD (NEAR BABCOCK FRAME)

 

 

150.   

METTLER-TOLEDO BENCH SCALE, NO MODEL PLATE VISIBLE, S/S PLATFORM 16 ½” X 21 ½”, ESTIMATED 50 LB. CAPACITY, DIGITAL HEAD ON ATTACHED POST, WITH PELOUZE MINI POSTAL SCALE – (DISCONNECTED AND STORED BEHIND BABCOCK FRAME)

 

 

 

 

MOBILE EQUIPMENT

 

 

151.   

“LITTLE MULE” MANUAL PALLET JACK, NO I.D. PLATE SEEN, 2500 LB. CAPACITY, YELLOW

 

 

152.   

YALE NARROW AISLE ELECTRIC STANDUP STRADDLE STACKER, MODEL RDE040GM4S090, S/N S251188, 4000 LB. CAPCITY, UNABLE TO VIEW HOUR METER, 612 HOURS AT LAST SERVICE 3/15/05, 2-STAGE MAST, 163” LIFT, INCLUDES (1) MAC BATTERY CHARGER MODEL “AUTOMATE 2200”, 24 VOLT

 

 

153.   

LEE ENGINEERING “PRESTO-LIFT” WALKIE STRADDLE STACKER, ESTIMATED 500-1,000 LB. CAPACITY, OLDER UNIT, DIRECT MOTOR DRIVE FOR HYDRAULIC LIFT, APPROX. 60” MAX. LIFT HEIGHT

 

 

154.   

WORLD FORKLIFT TRUCK, PROPANE, MODEL WFG 50, S/N 001081, 3,750 LB. CAPACITY, 3-STAGE MAST, 188” LIFT, SIDESHIFTER, OUTDOOR CUSHION TIRES, 14496 HOURS ON METER AS OF 3/22/11 INSPECTION DATE

 

 

155.   

FORD DIESEL BOX BODY TRUCK, MODEL L7000, SINGLE AXLE, DUAL FUEL TANKS, UNABLE TO FIND VIN #, SUPREME 20’ BOX BODY, APPROX. MID-1980’S VINTAGE, TRUCK INOPERABLE, MISSING CAP ON ONE FUEL TANK, TIRES DRY ROTTED, NO LONGER REGISTERED, REPORTED AS NON-RUNNING FOR 3 OR MORE YEARS, VALUED FOR PARTS ONLY

 

 

156.   

BOX VAN TRAILER, SINGLE AXLE, APPROX. 40’, BARN DOORS

 

 

 

 

TUB & PUSH TRUCKS

(SCATTERED THROUGHOUT PLANT & OUTSIDE)

 

 

157.   

(28) CANVAS HAMPERS, SOME PLASTIC-COATED VARIOUS SIZES, AVERAGE 18-24 CU. FT. CAPACITY, MANY WERE VERY POOR CONDITION

 

 

158.   

(13) S/S TUB TRUCKS AVERAGE 2’ X 4’ X 2 ½’ DEEP I.D., VARIED IN ACTUAL SIZES, SOME WERE 2’ X 2’ X 3 ½’ DEEP, MOSTLY GOOD CONDITION

 

 

159.   

(35) POLYETHYLENE TUB TRUCKS AVERAGE 43” X 43” X 40” DEEP I.D., MOSTLY GOOD CONDITION (25% FAIR TO POOR CONDITION)

 

 

160.   

(15) POLYETHYLENE TUB TRUCKS 4’ X 6’ X 3’ DEEP I.D., MOSTLY GOOD CONDITION (SOME AS NEW)

 

 

161.   

(8) POLYETHYLENE TUB TRUCKS, ROUND, 42” DIA. X 42” I.D., EXCELLENT CONDITION

 

 

162.   

(25) RIGGS & LOMBARD OR OTHERS S/S TUB TRUCKS AVERAGE 42” X 72” X 29” DEEP I.D., A FEW WERE SMALLER, MOSTLY GOOD CONDITION

 

 

163.   

(4) PUSH TRUCKS, OPEN-ENDED, WITH SIDING, ONE HAS RAIL SIDING, AVERAGE 42” X 12’

 

 

164.   

(3) PUSH TRUCKS, WOODEN, OPEN ENDS, WOOD SIDING, AVERAGE 42” X 10’, ONE IS 12’